standard pre hardened steel 1 2311 p20
LKM2311 P20 -1.2311 Prehardened to HB280 - 325 Pre-hardened plastic mould steel 0.37 1.9 1.45 0.2 - - Mould base/plate with high strength requirement for plastic injection mould; core/movable part of plastic injection mould without high surface finish requirement
Large plastic moulds with deep engravings and intensive impacts on the core. Pre-hardened Plastic Mold Steel is the logical development of 1.2311, a pre-hardened plastic mould steel for use in large moulds, which also have to display high core strength. The additional nickel content of 1.2738, AISI P20+Ni, 40CMND - plastic mould steel1.2738, 40CrMnNiMo8-6-4, AISI P20+Ni, 40CMND8 description. 1.2738 is a plastic mould tool steel, used mainly for plastic injection die moulds. It can be viewed as enhanced version of 1.2311 alloy, with 1% nickel content having a positive effect on hardenability. The steel is machinable, polishable, and suitable for texturing.
2311 Steel Properties; Nearest Equivalent :P20, ASSAB618; DIN 2311 is the Pre Hardened Plastic mould steel hardness distributed evenly in large cross sections that have excellent weldability with least hardness elevation, good mirror polishability and less streak texture making finishing easier. Size Section availability upto 255mm thickness. Bansal SteelsThe world's Hardest fully Prehardened tool steel with hardness all the way through. Material Categories:P20 2311; P20 2738; P20 2738 HH; TOOLOX 33 (33-35 HRC) TOOLOX 40 (40-42 HRC) TOOLOX 44 (45-47 HRC) Corrosion Resistant Steel:1.2083 ESR (Starvax Equivalent) 1.2316 ESR (Ramax Equivalent) HI3 (Hot die steel) 1.2344 ESR; D2 & D3; High speed steel
1.2738 tool steel is specially designed for plastic mold industry, especially for big steel mold parts. DIN 1.2738 tool steel is usually supplied as pre-hardened/quenched and tempered 280 320 HB hardness condition. With good machinability, DIN 1.2738 steels is with better polishability compared to 1 DME XPress A-Series Mold BaseThe all new DME XPress mold base sets the standard for immediate shipment with 58,000 combinations ready for Stress Relieved & Pre-Hardened Steel Increases your cutting speeds pre-hardened, 28-34 HRC #3 Steel:AISI P20, DIN 1.2311, G40CrMnMo7 or equivalent, stress-relieved, pre-hardened,
P20 Mold Steel. P20 Mold Steel is a versatile, low-alloy tool steel that is characterized by good toughness at moderate strength levels. The steel is commonly used for plastic injection mold cavities and tooling and for die casting dies for zinc. P20 is typically sold in the pre-hardened condition at a hardness of approximately 300 HBW. Mold steels P20,718 and H13 comparison EcomoldingNov 12, 2019 · How to Use:The P20 Steel is pre-hardened to 285-330HB (30-36HRC), which is equivalent to 618 of Sweden and GS-2311 of Germany. It can be directly used for molding, and boasts a great dimensional stability. Pre-hardened steel is able to meet the requirements for general applications, with a mold service life of up to 500,000 cycles.
P20 2311 Pre-hardened 28-34HRC Special Steel Plate. 1:3cr2mo 1.2311 p20 steel introduction aisi p20 steel plate material is a versatile, low-alloy tool metal this is characterised with the aid of good durability at mold strength ranges. P20 AISI P20 Tool Steel - Tool Steel Specification and AISI SAE P-20 is a pre hardened high tensile tool steelwhich offers ready machineability in the hardened and tempered condition, therefore does not require further heat treatment. This eliminates the risks, cost, and waiting time of heat treatment thus avoiding the associated possibility of distortion or even cracking.
P-20 is a plastic mould steel.It is a pre-hardened material with uniform hardness. Three grades of P20 are :- Din 1.2311, Din 1.2738, P20 Steel High Hard. P20+Ni Plastic Mould Steel DIN 2738 Tool Steel Ventura P20+Ni is an upgraded version of 2311 plastic mould steel, which is normally supplied in pre-hardened condition. Hardness in as provided condition 280-320 HB with having uniform hardness and the extra nickel content of 1% increases through hardening.
P20S TOOL STEEL ECONOMIZER. Pre-machined, P20S tool steel with machining allowance. Both bar ends saw cut. P20S (1.2312) Delivered pre-hardened this material is ready for use at approximately 280/325 H.B. Similar to P20 (1.2311) but with a higher sulpher content which provides much improved machinability. This grade is not suitable for polishing or other applications requiring a fine finish. Plastic Mould Steel - Guangzhou Changfeng Steel Co., Ltd CREAZY DEAL:Pre-hardened Die Steel 1.2311/P20 in Flat Bar & Round Bar & Block FOB Price:US $751 / Ton. Min. Order:20 Tons. Contact Now. Video. 1.2311/P20/PDS-3 special Steel Plate & Flat Bar & round bar or plastic Mould Min. Order:5 Tons. Contact Now. Video. 1.2311 P20 PDS-3 Hot Rolled / Forged alloy special Tool Steel Plate for plastic
Pre Hardened Plastic Mould Steel. As per P20 2311 Grade, P20 + Mo (2738 Grade) used for Core + Cavity Moulds, General purpose Moulds for Mass production and 2738 Grade for higher hardness, Bumper Moulds, Precision plastic moulds for uniform hardness, Excellent polish surface, good wear resistance , photo etching. Standard B30PH P20 1.2311 Big Plastic Mold Steel Plate Pre P-20 is supplied prehardened to 262/321 BHN. The balanced alloy composition of P20 ensures a uniform cross-sectional hardness. 2311 is in the group of tool steel for plastic mold.
offers 1,619 pre harden p20 steel products. A wide variety of pre harden p20 steel options are available to you, such as standard, processing service, and application.AISI P20 1.2311 3Cr2Mo - Waldun SteelAISI P20 1.2311 3Cr2Mo. AISI P20 plastic mold tool steel Manufacturer and Exporter,supplied with round,square,flat,block,and shaft etc. AISI P20 is a Cr-Mo alloyed steel as per ASTM A681.It is generally supplied in the hardened and tempered condition with hardness 285-340 HBW.Compared with P20+S ( 1.2312 ), it has good polishing and